One-sided edge banding machine IMA Combima Systems (2005)

IMA eins. Kantenanleimmaschine Combima Systems

- Automatic infeed table
- KFA unit
- Return system

Used single-sided edge banding machine
Manufacturer: IMA
Type: Combima Systems / I/R751220/R3
1 single-sided combination machine for trimming, edge gluing and edge finishing of panel-shaped workpieces made of wood and/or wood-based materials.
- Automatic infeed table
- KFA unit
Iiedpozuypljfx Aicjf
- Return system

Technical data "Workpiece":
Workpiece length
- min.: 238 mm
- max.: 2350 mm

Workpiece width
- min.: 142 mm
- max.: 800 mm

Workpiece thickness:
- min.: 8 - 40 mm

Technical data "Strip" (only for longitudinal processing):
Roll material:
- Paper edge bands & plastic edge bands: 0.3 - 3.0 mm
- Veneer edge bands: 0.5 - 3.0 mm

Edge height:
- min.: 14 mm
- max.: 45 mm

Technical data "Machine":
Variable workpiece overhang from the chain conveyor
(including edge with edge thickness 0.3-3 mm):
- min.: 40 mm
- max.: 80 mm
- PC control ICOS open
- Feed speed v=5-25 m/min, frequency-controlled drive
- Inclined roller table as infeed section

NC infeed system for front and carcass parts
- for length and width-independent automatic workpiece feed in single-sided edge processing machines.

Only for the production of strip material in the 2nd pass
- An additional stop rail, adjustable via NC axis.

Double milling unit 08.376:
- Controllable
- Motor 1 operating in the same direction and motor 2 operating in the opposite direction
- Reserve space on the unit carrier for a double trimming unit with electrical pre-installation for 2 x 6.6 kW.
- Heater 300 lg, 2x1.5 kW, for preheating the workpiece edge.
- Gluing unit 04.1570 system for straight edges and adhesive application to the workpiece. The edge thickness depends on the magazine used and is max. 3 mm.
- Adhesive application for workpiece thickness max. 50 mm
- 2 pre-melting tanks for PU adhesive
- 12-position edge magazine for roll material 0.3-3 mm thick. (8 slots up to 3 mm, 4 slots up to 1.3 mm)

Vertical roll holder for 12 rolls:
- max. roll diameter 850 mm
- max. edge height 45 mm
- Trimming unit 08.42, for 2 motors mounted on the upper pressure bar
- Pre-milling and milling unit with height sensor
- with 1 motor 1000 W
- Multi-profile / chamfer unit, with 2 motors 1000 W
- Contour milling unit KFA 30
- Multi-profile drawing blade unit
- Flat drawing blade 08.517
- Copy edging unit 08.604
- Edging unit 08.617-2
- Double milling stand 75.184, 1050 mm high, both stand sides can be used
- Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 6000 rpm
- Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 600 rpm
- Motor spindle for the use of the Hydro-Format tool system
- Return system, manufacturer Meinert

Note:
The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.