Veneer shears with cross veneer shearsJosting
EFS 2800 L + QFS 850
Veneer shears with cross veneer shears
Josting
EFS 2800 L + QFS 850
قیمت ثابت به اضافه مالیات بر ارزش افزوده
€۱۵٬۹۰۰
سال ساخت
۲۰۰۹
وضعیت
کارکرده
موقعیت
Bitburg 

تصاویر نشان میدهند
نمایش نقشه
اطلاعات دستگاه
- نام دستگاه:
- Veneer shears with cross veneer shears
- تولید کننده:
- Josting
- سال ساخت:
- ۲۰۰۹
- وضعیت:
- بسیار خوب (کارکرده)
قیمت و مکان
قیمت ثابت به اضافه مالیات بر ارزش افزوده
€۱۵٬۹۰۰
- موقعیت:
- Südring 37, 54634 Bitburg, Deutschland

تماس بگیرید
جزئیات پیشنهاد
- شناسه آگهی:
- A20830972
- بهروزرسانی:
- آخرین بهروزرسانی در ۰۴.۱۰.۱۴۰۴
توضیحات
Josting Veneer Guillotine with Cross-Cutting Machine
The machine precisely cuts veneer bundles in a straight and parallel manner. For all types of veneer, tight jointing after cutting is ensured.
Technical features:
● Highest cutting quality thanks to an oscillating knife movement, pulling at an angle of approx. 20°.
● Parallel fence with motorized rapid adjustment, fine adjustment, and digital measurement display for cutting parallel widths and strips.
● The green alignment light clearly marks the cutting line.
● Alignment grooves and an angle stop on the machine table facilitate positioning of the veneers.
● The wide pressure beam presses even wavy veneers flat and level before cutting.
● The trim-cut function hydraulically adjusts the knife beam by 0.9 mm. Square cutting edges are achieved by pre- and post-cutting with pressed veneer bundles.
● Cutting veneers across the grain is possible thanks to the powerful crank drive.
● The heavy construction safely absorbs the high pressing and cutting forces.
● Precise and durable parallel guidance of machine components.
● Full utilization of the knife due to 30 mm regrinding capability.
● Low energy consumption and reduced noise levels due to intermittent drive operation.
● Safety features include light curtain interlock, two-hand operation, safety electrical control system, and rear safety guard in accordance with occupational safety regulations.
● The machine can also cut paper, foils, plastics, and other materials.
Cutting length: 2800 mm
Insertion height: 80 mm
Parallel fence range: 20 - 570 mm
Pressure beam: 2 pressure stages
Knife beam: Brake motor, gearbox crank drive
Parallel fence: Three-phase motor, positioning drive
Electrical connection: 7.7 KW
Footprint (with parallel fence): 414 x 155 cm
Height: 170 cm
Weight: 3500 kg
Includes: KUPER QFS 850 cross-veneer guillotine for trimming veneer packs
Location: ex-site customer
- immediately available -
System must be dismantled by the buyer
Ltodpfx Afox N A D Ropea
آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.
The machine precisely cuts veneer bundles in a straight and parallel manner. For all types of veneer, tight jointing after cutting is ensured.
Technical features:
● Highest cutting quality thanks to an oscillating knife movement, pulling at an angle of approx. 20°.
● Parallel fence with motorized rapid adjustment, fine adjustment, and digital measurement display for cutting parallel widths and strips.
● The green alignment light clearly marks the cutting line.
● Alignment grooves and an angle stop on the machine table facilitate positioning of the veneers.
● The wide pressure beam presses even wavy veneers flat and level before cutting.
● The trim-cut function hydraulically adjusts the knife beam by 0.9 mm. Square cutting edges are achieved by pre- and post-cutting with pressed veneer bundles.
● Cutting veneers across the grain is possible thanks to the powerful crank drive.
● The heavy construction safely absorbs the high pressing and cutting forces.
● Precise and durable parallel guidance of machine components.
● Full utilization of the knife due to 30 mm regrinding capability.
● Low energy consumption and reduced noise levels due to intermittent drive operation.
● Safety features include light curtain interlock, two-hand operation, safety electrical control system, and rear safety guard in accordance with occupational safety regulations.
● The machine can also cut paper, foils, plastics, and other materials.
Cutting length: 2800 mm
Insertion height: 80 mm
Parallel fence range: 20 - 570 mm
Pressure beam: 2 pressure stages
Knife beam: Brake motor, gearbox crank drive
Parallel fence: Three-phase motor, positioning drive
Electrical connection: 7.7 KW
Footprint (with parallel fence): 414 x 155 cm
Height: 170 cm
Weight: 3500 kg
Includes: KUPER QFS 850 cross-veneer guillotine for trimming veneer packs
Location: ex-site customer
- immediately available -
System must be dismantled by the buyer
Ltodpfx Afox N A D Ropea
آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.
تأمینکننده
توجه: به صورت رایگان ثبتنام کنید یا وارد شوید, تا به تمام اطلاعات دسترسی داشته باشید.
ثبت شده از: 2004
ارسال درخواست
تلفن & فکس
+49 6561 ... آگهیها
آگهی شما با موفقیت حذف شد
یک خطا رخ داده است

































