Wide belt sander

SCM S900 RRT 135

SANDYA 900 - WIDE-BELT CALIBRATING AND FINE-GRINDING MACHINE S900 RRT 135 KEY FEATURES 2,620 MM LONG GRINDING BELTS FOR OPTIMAL SURFACE QUALITY AND PRODUCTIVITY PHOTO CELLS WITH SYSTEM WITH BACKGROUND SUPPRESSION: THE CORRECT CENTERING OF THE GRINDING BELT IS ALWAYS GUARANTEED FLOATING PRESSURE ROLLERS: ACCURATE AND CORRECT SUPPORT OF THE WORKPIECES UNDER ALL WORKING CONDITIONS TECHNICAL DATA Working width mm 1,350 Min./max. working height mm 4-170 Grinding belt width mm 1,370 Grinding belt length mm 2,620 Motor power 1st unit kW (HP) 11 (15) Motor power 2nd/3rd unit kW (HP) 11 (15) Gear motor kW (HP) 0.6/1.3 (1.8/1.7) Feed speed m/min 4.5/9 GENERAL FEATURES: Machine frame and work table* Steel structure with electrical control cabinet on the front of the machine * Insertion of the grinding belts from the left side of the machine * motorized table height adjustment * Main motors integrated into the machine frame Electrical equipment* Electromechanical control panel on the left front side of the machine * automatic star-delta starter for the main motor * motor protection switches for the motors * motors in insulation class IP 54 Safety and protective devices* automatic brake for immediate stopping of the units * emergency stop switch at the workpiece infeed * emergency stop switch at the workpiece infeed and outfeed * lockable main switch * automatic emergency shutdown of the machine in case of: - grinding belt breakage - grinding belt not tensioned - protection against lateral deflection of the grinding belt - lack of compressed air - overload of the main motors Note: the standard version with 400 volts 50 Hz requires a three-phase power supply + neutral conductor + earth conductor. If the 400-volt power supply is without a neutral conductor, a single-phase transformer must be ordered in addition from the price list. The same transformer must also be ordered for a machine with a voltage higher than 400 volts, regardless of whether a neutral conductor is available or not. Machine version with 220 or 230 volts (50 or 60 Hz) is available at an additional cost (see price list). BASIC MACHINE STANDARD EQUIPMENT - R175/85 rubber-coated calibrating roller, diameter 175 mm, 85 Shore - 1st position - R220/65 rubber-coated calibrating and grinding roller, diameter 220 mm, 65 Shore - 2nd position - Hard grinding shoe with manual adjustment of the working height - Replaceable graphite cloth - Motor power 1st unit 11 kW (15 HP) - Motor power 2nd and 3rd unit 11 kW (15 HP) - Electronic ammeter for the main motor to display the current consumption - Electronic display of the working height - Electronically controlled grinding belt oscillation - Rubber pressure rollers - Recoil protection at the infeed before the first unit - Rubber feed belt 60 SH - Roller table with two rollers at the infeed and outfeed of the work table - Belt feed with two speeds 4.5 / 9 m/min with gear motor - Automatic belt centering European safety regulations (CE marking) 1 piece SANDYA 900 RRT 135 - Calibrating and fine-grinding machine 1 piece First and second "R" unit with roller and third "T" unit with grinding shoe Voltage 400 EU 1 piece Frequency 50 Hz 1 piece "C plus" version for RRT 1 piece with: - pneumatic switching on and off of the roller – 1st unit "R" - pneumatic switching on and off of the roller – 2nd unit "R" - "MESAR 46" electronic oscillating grinding shoe - electronic adjustment of the working height - Selection of belt running direction 2nd grinding belt 1
Redpfs Aflwyex Abnsch

آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.