تریلر نیمه باز با چادر برزنتی

KÖGEL 3-Achs-Cargo-Coil-Pritschensattelanhänger

You will find our complete range of vehicles, including immediately and short-term available units, on our website.

Excerpt of equipment. Full equipment details available on request.

Chassis
* Coil trough (approx. internal length 9,000 mm, designed according to VDI guideline 2700) for accomodating coils with a diameter from min. 900 mm to max. 2,100 mm

Running Gear
* Axle lift mechanism on axle 1
* Three-axle SAF INTRADISC unit with disc brakes, approx. Ø 430 mm, ET 120
* Air suspension with approx. 180 mm lift
* Tyres – 6x 385/65 R 22.5, 160J – brand at our choice
* 6 steel rims 22.5 x 11.75, offset approx. 120 mm (ET 120)
* Brake / air suspension system
* EBS system 2S/2M with stability program (includes ABS/ALB function)
* EBS connection ISO 7638 (without wiring)
* Parking brake as spring-actuated brake, external pneumatic connections as well as external EBS diagnostic connection via ISO 7638 plug
* WABCO EBS system
* Air suspension system incl. 1 lifting and lowering valve, installed left side in direction of travel, behind axle unit
* Ride height automatically adjusts

Floor
* Both sides installed version
* Steel pallet stop bars with VarioFix hole pattern (bolted), left and right in the direction of travel, for internal width approx. 2,468 mm (loading height under external beam is reduced by approx. 20 mm)
* Floor panels approx. 30 mm thick, multi-bonded plywood, recessed in coil trough area
* Coil trough side walls lined with approx. 18 mm thick plywood panels
* Continuous joint sealing around the floor
Chodpfx Aoxvgqlsg Ief
* Coil trough cover entirely made of wood, with panel flooring approx. 27 mm thick

* Pocket holes for square tube stanchions approx. 80 x 80 mm
* Arrangement per drawing A2:
* 2 pairs on longitudinal beam at 1st and 2nd positions
* 8 pairs on external frame

* 8 pairs of pocket holes in coil trough to accommodate square tube stanchions approx. 80x80 mm
* Arrangement: 1st pair at front of trough, 2nd – 7th pair as per series drawing, 8th pair at rear of trough

Body
* Meets body strength requirement EN 12642 XL (VDI 2700)
* Certified for payload approx. 27,000 kg
* Front wall at body height with aluminium volume corner stanchions
* Riveted with aluminium hollow profiles, bolted/riveted to frame
* 1 pair of lashing rings per EN 12640
* Front wall interior reinforced with approx. 12 mm plywood with anti-slip film surface, approx. 1,250 mm height
* Double-leaf rear portal door made of aluminium, approx. 2,630 mm internal clearance
* 4 integrated locking rods (2 left, 2 right)
* Rear portal corner stanchions bolted, made of steel at portal height with additional impact guard up to first door hinge
* Corner stanchions on both sides extendable sideways by approx. 500 mm for loading/unloading
* To operate, sliding roof must be pushed forward and rear doors opened
* 5 pairs of slots for load securing at rear corner stanchions, side wall
* 3 pairs KÖGEL sliding stanchions with receptacle approx. 600 mm high for 5 insertable slats stacked above floor edge. Fixed to outer frame
* 5 rows of slat holders consisting of plug-in slat pockets on sliding stanchions and variable supports in the corner stanchions
* Variable supports as spacers for insertable slats (16 pcs.), fitted in the storage compartment of sliding and corner stanchions (height approx. 100 mm above flooring)
* 4 rows of V-shaped aluminium slats at the sides
* VarioFix steel hole outer frame with 3 pairs of stanchion brackets
* 2 additional pairs of stanchion brackets on the ou

آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.