Baler 100 t with conveyorsystem VK 8818 R-FU

HSM GmbH + Co. KG, Deutschland VK 8818 R-FU

Technical data baler:
Manufacturer HSM GmbH + Co. KG, Germany
Type VK 8818 R-FU
Year of construction 2015
Operating hours 19,750 hours, as of July 2025
Number of bales pressed: 24,760 bales, as of July 2025
Main press force 1000 kN
Specific pressing force 120 N/cm²
Pressing force cutting edges free rammer 121 kN
Dimensions of feed chute 970 x 1,800 mm
Theoretical cycle time in idle mode 8.3 seconds
Theoretical throughput capacity 643 m³/hour
Bale dimensions 1,100 x 750 mm, the length is variable 600 up to 2000 mm
Drive power 2 x 45 kW frequency-controlled
Connected load 110 kW
Total current consumption 213 A
Fuse protection 250 A slow-blow
5-fold horizontal tying, fully automatic
Throughput rates with a
bulk density of 20 kg/cbm 12.86 t/hour
Bulk weight of 50 kg/cbm 32.15 t/hour
Bale weights with a bale length of approx. 1.2 m 650 up to 750 kg/bale, depends on materiel
Hydraulic oil tank capacity 2000 litres
PLC control Siemens S7-300
Siemens TP 700 control panel
Press dimensions assembled 12,130 x 4,800 x 3.270 mm (l x w x h)
Press dimensions with conveyor system 35,000 x 8,480 x 7,745 mm (l x w x h)
Transport weight baler approx 33 t (Main press approx. 12 t, press channel with bale clamp approx. 10 t)

Special machine equipment:
Access locking by means of key transfer system
Electro-hydraulic locking of the press carriage during the tying process so that the press plunger does not change position with highly expansive materials

Additional optional equipment ordered:
Frequency-controlled main drive, 2 x 45 kW, with up to 40 % energy savings compared to the standard motorisation 2 x 45 kW, with the same power output
Csdpfx Abexb Dvvefsrh
Manual switch-off or switch-on of the number of strapping wires to save on strapping wire for non-expansive material
Cutting-edge frei rammer with 121 kN pressing force
Sensory wire monitoring, with press switch-off in the event of wire breakage or wire end
Bale chute
Visual warning signal, mounted on the control cabinet

Condition of the baler:
The entire baling system (baler and conveyor belt) is in good, operational condition and is cleaned, lubricated and maintained by the operator on a weekly basis in accordance with the manufacturer's specifications.

Technical data for the chain belt conveyor:
Manufacturer Stadler Anlagenbau GmbH
Typ chain belt conveyor KF 1800
Year of construction 2015
Belt speed 0,36 m/sec.
Length feeding conveyor 7,000 mm
Length elevating conveyor 14,500 mm
Length goose neck 1,550 mm
Grade 30°
Nominal width 1,800 mm
Effecting width 1,638 mm
Height conveyor over all 7,745 mm
Pit dimensions to conveyor belt 11,200 x 3,000 x 1,250 (l x w x h)

Scope of delivery:
The conveyor belt, the transverse distribution belt and the baling press are for sale, with bale chute but without wire pulling stations and without wire.

Comments:
The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.