Engel duo 2400/650

Engel duo 2400/650

This Engel duo 2400/650 electrical injection moulding machine was manufactured in 2019. It features a screw diameter of 60/70/80 mm, a screw stroke of 315 mm, and a maximum injection capacity of 890 cm³. The clamping force reaches up to 6500 kN with a maximum mold weight of 11000 kg. Consider the opportunity to buy this Engel duo 2400/650 electrical injection moulding machine. Contact us for more information about this machine.

Additional equipment

• Oil Reservoir Capacity - Injection Unit: 500 l
• Maximum Cooling Power (32°C Water Inlet): 29.40 kWcool
• Water Consumption (32°C): 4.80 m3/h

Machine Benefits

Qualitative Machine Benefits

• The machine has electric water batteries (4 e-flomos with 8 circuits each).
• The injection units are fitted with accumulators which enable a high injection pressure of up to 2400 bar with a 60 mm screw.
Technical Machine Benefits

• Maximum injection capacity: 890 cm³
• Screw torque: 2000 nm // maximum screw speed @ reduced torque: 275 min-1
• Reduced torque @ maximum screw speed: 1600 nm
• Recovery rate (3-zone screw): 51 g/s // recovery rate (barrier screw): 67. 1 g/s
• Injection rate: 353 cm³/s
• Nozzle stroke: 950 mm
• Ld ratio: 24. 0
• Heating zones incl. Nozzle: 8 // heating wattage: 27. 5 kwel
• Opening force with pressure pad: 510 kn
• Maximum distance between platens: 1750 mm

Extra Information

Dimensions & Weight

• Drop Out Chute Width: 1100 mm
• Weight of Clamping Unit: 20,000 kg
• Maximum Mold Weight (Moving Platen): 7,330 kg
• Maximum Mold Weight (Stationary Platen): 7,330 kg
• Maximum Mold Weight (Total): 11,000 kgCycle Data (Euromap 6)
• Stroke: 700 mm
• Dry Cycle Time: 2.9 s
Control System: Monocompute CC300
Main Features
• 21.5” full HD touchscreen
• USB interface / Ethernet connection
• E-move control element
• 3 keycards for user login
• Graphic symbols for cycle control
• Screen languages: German, English
• Acoustic error signal / Signal light for error displayPrograms & Monitoring
• Power Control: optimizes motor performance during dispensing
Codpfx Alsy D Npceyorb
• Mould parallelism measurement
• IQ Weight Monitor: monitors shot weight & viscosity
• IQ Weight Control: automatic injection parameter adjustment during fluctuations
• Quality monitoring interface (injection time, dosing time, pressure, cycle time)
• Continuous ejection possible when monitoring is deactivated
Clamping Unit & Plates

• Reinforced clamping plates (FAP & BAP +50 mm each)
• Reduced min./max. tool height and panel distance (–100 mm due to reinforcement)
• FAP: smallest possible platen opening, spherical calotte minimized
• BAP: without ejector opening
• Additional threads according to EUROMAP VOL1
• Centering grooves according to drawing
• Plate ejector – Variant A (adapted to clamping pattern)
• Safety interface for ejector
Hydraulics & Core Pulls

• Hydraulic core pull:
• 1-fold on moving platen
• 2-fold on fixed platen
• 2-fold on moving platen with PQ proportional valve, volume measurement, pressure/speed adjustment
• Interface for intermediate core pull position
Mold Heating & Cooling

• Mold heating: 16 circuits, max. 40 kW heat output (Euromap 14)
• Temperature monitoring interface (moving & fixed platen)
• 4-fold hydraulic mold nozzle control
• Separate cooling water connection (tool & machine)
• Temperature control unit interface: Engel protocol, 20 mA current loop
• 4-way flow regulator (0–10 l/min)
• Hose specification: max. 90 °C / 4 bar
• Hoses for mold cooling