Machining centerDeckel MAHO
DMU50
Machining center
Deckel MAHO
DMU50
سال ساخت
۲۰۰۵
وضعیت
کارکرده
موقعیت
Stefansdorf 

تصاویر نشان میدهند
نمایش نقشه
اطلاعات دستگاه
- نام دستگاه:
- Machining center
- تولید کننده:
- Deckel MAHO
- مدل:
- DMU50
- سال ساخت:
- ۲۰۰۵
- وضعیت:
- خوب (دست دوم)
- قابلیت عملکرد:
- کاملاً عملیاتی
- ساعات کارکرد:
- ۸۴٬۵۶۴ h
قیمت و مکان
- موقعیت:
- Stefansdorf 20, 4722 Peuerbach, AT
تماس بگیرید
جزئیات فنی
- مسافت جابجایی محور X:
- ۵۰۰ میلیمتر
- مسافت حرکت محور Y:
- ۴۵۰ میلیمتر
- مسافت حرکت محور Z:
- ۴۰۰ میلیمتر
- حرکت سریع محور X:
- ۱۲ متر/دقیقه
- حرکت سریع محور Y:
- ۱۲ متر/دقیقه
- حرکت سریع محور Z:
- ۱۲ متر/دقیقه
- نرخ تغذیه محور X:
- ۱۰ متر/دقیقه
- نرخ تغذیه محور Y:
- ۱۰ متر/دقیقه
- سرعت پیشروی محور Z:
- ۱۰ متر/دقیقه
- توان نامی (ظاهری):
- ۱۷ کیویای
- تولیدکننده کنترلر:
- iTNC 530 Heidenhain
- مدل کنترلر:
- iTNC 530 Heidenhain
- ارتفاع کل:
- ۲٬۵۰۰ میلیمتر
- طول کل:
- ۳٬۰۰۰ میلیمتر
- عرض کل:
- ۳٬۰۰۰ میلیمتر
- عرض میز:
- ۵۰۰ میلیمتر
- طول میز:
- ۶۵۰ میلیمتر
- ظرفیت بار میز:
- ۲۰۰ کیلوگرم
- سرعت اسپیندل (دقیقه):
- ۲۰ دور/دقیقه
- حداکثر سرعت اسپیندل:
- ۱۰٬۰۰۰ دور/دقیقه
- ساعت کارکرد اسپیندل:
- ۲۲٬۸۵۵ h
- توان موتور اسپیندل:
- ۱۳٬۰۰۰ وات
- تعداد جایگاهها در مگزین ابزار:
- ۱۶
- طول ابزار:
- ۳۰۰ میلیمتر
- قطر ابزار:
- ۱۳۰ میلیمتر
- وزن ابزار:
- ۶ g
- تجهیزات:
- سرعت چرخش به طور نامحدود قابل تنظیم
جزئیات پیشنهاد
- شناسه آگهی:
- A18328921
- بهروزرسانی:
- آخرین بهروزرسانی در ۰۳.۱۱.۱۴۰۳
توضیحات
The machine is in good condition. A few things have been redone and freshened up.
The following has been overhauled:
-Complete X-axis bearing including ball screw and bearing
-Various hydraulic components
-Tool changer reset and sensors replaced
-New door switch installed
-New discs installed (unfortunately already got some flying chips again)
-New coolant pump
-New screen, as it was defective
-New handwheel HR410
The machine does not have many spindle hours or switch-on hours. The machine has never seen a series production and has always been operated sensibly. Warm-up programs etc.
We are tool and mold makers, so we tend to do more complex contours rather than heavy machining.
I am only selling this because I need a simultaneous machine and also more travel paths.
Technical data:
Year of manufacture 2005
x-travel 500 mm
y-travel 450 mm
z-travel 400 mm
Control iTNC 530 Heidenhain
Iedpevtnm Hjfx Acyeih
Main spindle
Speed range - main spindle 20 - 10,000 rpm
Drive power - main spindle 9 / 13 kW
Torque 57 / 82 Nm
Tool holder SK 40
Rotary table
Table clamping area 630 x 500 mm
Swivel range -5 / +110 °
Max. table load 200 kg
T-slots 14 H7
T-slots - distance 63 mm
C-axis +/- 360 °
Feeds:
Rapid traverse (X / Y / Z) 12 m/min
Feed rate 10,000 mm/min
Tool changer:
Tool positions 16 pos.
Max. tool weight 6 kg
Max. tool length 300 mm
Max. tool diameter 80 mm
Max. tool diameter with free adjacent box 130 mm
Tool holder SK 40
Total power requirement 17 kVA
Machine weight approx. 3.6 t
Space requirement approx. 3.0 x 3.0 x 2.5 m
Tool milling machine - Universal
DECKEL MAHO - DMU 50
Attention: no chip conveyor and no automatic measuring probe!
- 5 axes (3+2)
- WITHOUT tools
Attached are pictures of the machine. The machine was intentionally not cleaned before taking the pictures, so it is in the "chip" and is used daily. You can also see the hours of the machine there.
Kinematics and geometry are OK. for our needs, but could possibly be re-measured.
We have never had any crashes etc.
آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.
The following has been overhauled:
-Complete X-axis bearing including ball screw and bearing
-Various hydraulic components
-Tool changer reset and sensors replaced
-New door switch installed
-New discs installed (unfortunately already got some flying chips again)
-New coolant pump
-New screen, as it was defective
-New handwheel HR410
The machine does not have many spindle hours or switch-on hours. The machine has never seen a series production and has always been operated sensibly. Warm-up programs etc.
We are tool and mold makers, so we tend to do more complex contours rather than heavy machining.
I am only selling this because I need a simultaneous machine and also more travel paths.
Technical data:
Year of manufacture 2005
x-travel 500 mm
y-travel 450 mm
z-travel 400 mm
Control iTNC 530 Heidenhain
Iedpevtnm Hjfx Acyeih
Main spindle
Speed range - main spindle 20 - 10,000 rpm
Drive power - main spindle 9 / 13 kW
Torque 57 / 82 Nm
Tool holder SK 40
Rotary table
Table clamping area 630 x 500 mm
Swivel range -5 / +110 °
Max. table load 200 kg
T-slots 14 H7
T-slots - distance 63 mm
C-axis +/- 360 °
Feeds:
Rapid traverse (X / Y / Z) 12 m/min
Feed rate 10,000 mm/min
Tool changer:
Tool positions 16 pos.
Max. tool weight 6 kg
Max. tool length 300 mm
Max. tool diameter 80 mm
Max. tool diameter with free adjacent box 130 mm
Tool holder SK 40
Total power requirement 17 kVA
Machine weight approx. 3.6 t
Space requirement approx. 3.0 x 3.0 x 2.5 m
Tool milling machine - Universal
DECKEL MAHO - DMU 50
Attention: no chip conveyor and no automatic measuring probe!
- 5 axes (3+2)
- WITHOUT tools
Attached are pictures of the machine. The machine was intentionally not cleaned before taking the pictures, so it is in the "chip" and is used daily. You can also see the hours of the machine there.
Kinematics and geometry are OK. for our needs, but could possibly be re-measured.
We have never had any crashes etc.
آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.
تأمینکننده
توجه: به صورت رایگان ثبتنام کنید یا وارد شوید, تا به تمام اطلاعات دسترسی داشته باشید.
ثبت شده از: 2019
ارسال درخواست
تلفن & فکس
+43 7276 ... آگهیها
این آگهیها ممکن است برای شما نیز جالب باشند.
آگهی کوچک

۴٬۲۰۰ km
Deckel MahoDMU 50 EVO Linear
آگهی کوچک

۳٬۹۸۳ km
DECKEL- MAHODMU50
آگهی کوچک

۴٬۴۱۸ km
Deckel MahoDMU 50 eVolution
آگهی کوچک

۴٬۰۹۷ km
Deckel MahoDMU 50 EVO LINEAR
آگهی کوچک

۴٬۱۳۶ km
Deckel MahoDMU 50 eVo
آگهی کوچک

۴٬۱۶۹ km
Deckel MahoDMU 50 T
آگهی کوچک

۴٬۲۳۸ km
DECKEL MAHODMU 50 T
آگهی کوچک

۴٬۰۹۷ km
Deckel MahoDMU 50 T
آگهی کوچک

۴٬۱۳۶ km
Deckel MahoDMU 50 T Heidenhain Mill Plus
حراج
به پایان میرسد در
d
h
min
s
حراج پایان یافت

۴٬۳۱۵ km
DECKEL MAHODMU 50 T
آگهی شما با موفقیت حذف شد
یک خطا رخ داده است