تریلر کم‌ارتفاع نیمه‌کشنده

MÜLLER-MITTELTAL Tieflader TS3-RM ML30,0 mit Radmulden Lenkachse

Müller-Mitteltal Low-loader with Wheel Recesses TS 3 RM ML 30.0, 2 Loading Heights and Ramps

* Fifth wheel load increase from 12 t to 18 t incl.
Kingpin mounted in: Second kingpin position 2", kingpin up to and incl.
5th wheel height 2,750 mm. Rear turning radius approx. 2,400 mm in clear width
(a minimum clearance of 150 mm is recommended). Forward turning radius
1,480 mm or 1,570 mm with spare wheel. Note: Sufficient clearance to the
towing vehicle must be ensured by the customer.

* Extension parts for the wheel recesses at the front and bottom at the rear (205 mm deep). 6 pieces incl. insertion boards for wheel recesses at the rear. Board holder as receiving shafts according to code 09.112. Aluminum compressed air tank instead of steel.

* Smartboard control box mounted on the trailer as an information tool with pressure sensors incl., exclusively for overall axle load display. Display option can be selected via the control box or in the truck via the EBS air suspension system (truck manufacturer-dependent).

* ?SP-Combination Package: Tool box with 45° corners made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, on the fifth wheel platform, W=2,480 x H=500 mm with a folding lid on top, side doors and sloping corners. Incl. aluminum side walls that can be folded down to the fifth wheel platform (500 mm high), aluminum rear wall plugged in (150 mm high), aluminum side panels painted inside and out in RAL 9006 white aluminum. Incl. rear uprights, foldable and detachable, galvanized (without topcoat). Incl. bolted front structure. Length of front cross member to 5th wheel height 3,935 mm. Forward turning radius, without spare wheel, at 5th wheel height 2,450 mm or 2,750 mm, approx. 1,750 mm or approx. 1,480 mm.
* 2 container locking mechanisms recessed into the front cross member.

* 3 receiving shafts under the fifth wheel platform for storing optional aluminum ramps or wooden planks for covering the wheel recesses.

Pjdpfx Ajy R Ipuspbjgr
* Folding/extendable outrigger (galvanized) and wooden planks for widening incl. (not on the rear slope), plank holder on the fifth wheel platform (the track width of the load may be a maximum of 2,500 mm).

* Second LED position light on the warning package at the front and rear (double lighting), only in combination with the warning package.

* 2 LED reversing lights on the rear of the trailer, switched with reverse gear (suitable for 12 V and 24 V), max. 2 additional lights in total.

* 7-pole socket on the rear, wired for overhang lighting with tail light (58 R) and ground.

* Rubber mat on the loading ramp on the left and right (approx. 860 mm long) 190 07644 rubber strip, on the inner plank of the one-piece ramps.

* Central lubrication system fully automatic with pump (24 V), grease tank and integrated trailer control, without connection to the ramps (in the case of steering: incl. connection of the distributor of the fifth wheel platform). Note: Only possible with towing vehicles with a 24 V lighting system!

Intermediate sale and errors are expressly reserved!
Sale exclusively subject to our general terms and conditions (AGB).

Important note - Important information: Despite careful checking of all details in our offer, errors may occur. Some of these are caused by transmission errors in the systems of the various platform providers. Therefore, we would like to point out that all information is provided without guarantee and does not c

آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.