نیمه یدک‌کش با سکوی کاری

KÖGEL 3-Achs-Sattelanhänher Multi Chassis

You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website.
Excerpt from the equipment list:
Complete equipment available upon request.

Chassis
* Regular ladder frame in lightweight steel construction with continuous crossmembers
* Frame extended forward
* Coupling plate approx. 8 mm thick, with a 2-inch fifth-wheel kingpin according to DIN 74080 / ISO 337

Axle
* Axle lift mechanism on axle 1, with fully automatic, load-dependent axle lift control
* Starting assist: Activated via 3x brake application, 30% overload up to a speed of 25 km/h
* Operation on the chassis via switches
* Also possible from the cab (switch in the cab required - PIN 12)
* Manufacturer to be chosen: Kögel
* Three-axle unit, with disc brakes Ø approx. 430 mm, offset approx. 120 mm
* Air suspension with approx. 180 mm travel

Vehicle tires
* Wheels with internal sensors according to UN ECE R141
* Tires 6x 385/65 R 22.5, ATHOS HG 2144 (164J)

Chassis components
* Fifth-wheel mounting (manufacturer to be chosen by Kögel) mechanically with leveling foot, 24 t lifting capacity.
* One-sided operation on the driving side (right side).
* Splash protection system (spray mist suppression) according to Regulation (EU) No. 109/2011 for three-axle unit with tires 385/65 R22.5
* Consisting of 1 pair of quarter-circle fenders in front of the axles
* 1 pair of straight fenders with mud flaps between the 1st and 2nd axles and 1 pair of quarter-circle fenders with mud flaps behind the axles.
* Lateral protection device according to ECE-R73.
* 2 plastic toolboxes, waterproof, dimensions (internal) approx. 525 x 390 x 410 mm. Installation at the rear, 1x on the left and 1x on the right.
* High, rigid rear underrun protection made of steel according to ECE-R58
* 1 pair of retractable warning signs (approx. 280x280mm) for over-width loads, retroreflectively red / white, with LED lighting, spiral cable and plug connection.

Brake / Air Suspension System
* EBS system 2S/2M with stability program (includes ABS/ALB function)
* EBS plug connection ISO 7638, (without connection lines)
* Parking brake as spring-loaded brake, external pneumatic connections and external EBS diagnostic connection via ISO 7638 plug connection.
* WABCO EBS system
* Air suspension system incl. 1 lifting and lowering valve, mounted on the driving side behind the axle unit
* Driving position is automatically adjusted.
* 2 non-interchangeable coupling heads at the front
* Air tank for braking system and air reservoir made of steel (EN 286-2)

Floor
* Plate floor approx. 30 mm thick
* Floor sealed around the perimeter, pocket rails for square tube inserts approx. 80 x 80, arrangement according to drawing
* 8 pieces of pocket rail strips (18 pocket rails per strip: 4 pieces each on the outside + 10 pieces in the middle)

Front Wall
* Storage for max. 20 square tube inserts 80 x 80 (length 1,990 mm) on the inside of the front wall
* Front wall approx. 2,000 mm high with steel corner posts, with profiled steel sheet, screwed/riveted to the frame.
* 2 pairs of lashing points (permissible lashing force approx. 1,000 kg per ring) on the front end according to EN 12640.
* Side wall VarioFix steel hole outer frame without rail storage
Prjdpfjz N Nxdex Abnjc
* 21 pairs of lashing eyes in the outer frame (according to EN 12640), permissible pulling force approx. 5,000 kg per ring.

Impact Protection
* 1 pair of steel impact buffers approx. 160x85x85mm mounted on the frame end plate

آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.