Interior simulation box

IPETRONIK IPETRONIK Innenraumsimulationsbox

IPETRONIK interior simulation box
Here we offer you an IPETRONIK indoor simulation box.
Technical data and description of the equipment:
IPETRONIK interior simulation box ( new and unused ).
The interior simulation box is intended to simulate the passenger compartment for tests in recirculation mode.
It has a variable interior space from 1,8 to 4m³.
The exhaust air volume flow from the front evaporator or the air conditioning unit is fed into the interior in a controlled manner.
Only rear evaporators installed in the passenger compartment are tested with the interior simulation box.
The insulation chamber is mounted on an aluminum profile frame with rollers.
A light is installed in the chamber.
The box is protected against overtemperature by a safety thermostat (Esti).
If the permissible temperature is exceeded, a glass cartridge in the ESTI is destroyed. The installation is stopped.
(TRIGGER TEMPERATURE: 80°C)
Technical data of the isolation chamber:
Dimensions:
Outside: width 1.860 mm depth 2.360 mm height 1.360 mm
Inside: Width 1.700 mm Depth 2.200 mm Height 1.200 mm
Insulation:
80 mm polyurethane rigid foam, foamed CFC-free, U-value 0.27 W/m2K, building material class B1 according to DIN 4102.
Technical data and description of the system:
Connection: Tongue and groove system with foamed-in eccentric closing hooks.
Surfaces:
Both sides: 0.8 mm stainless steel sheet 1.4301, ground, grain 320
Bottom finish:
2.0 mm stainless steel sheet 1.4301, SM rhombus, anti-slip,
bottom beveled 90 ° all around (approx. 15 mm), bottom plate flush with wall plate,
Pressure distribution plate made of laminated wood, 1,500 N/rubber wheel loadable (contact area > 4 cm2),
30,000 N/m2 surface load, floor joints completely welded, welded-in stainless steel pipe as floor drain,
led out through the floor to the bottom
Chamber door:
Hatch door, 1-leaf, 800 x 1200 mm i.l., DIN left, heated door frame (230 V),
Fgsdelypy Espfx Ahxoh
heating bands silicone-free, 4-sided sealing profile made of EPDM,
pess lever lock, lockable, emergency release,
heated viewing window, 500 x 500 mm, triple glazed,
surface heating (230 V), frame heating (230 V), heating controlled on site,
silicone-free lipping
Movable wall:
1680 x 1180 mm, 80 mm rigid polyurethane foam, 0.8 mm stainless steel sheet 1.4301 on both sides,
ground, grit 320, with protective foil, closed on both sides with sheet metal
(The rear wall is manually infinitely adjustable for volume change).
Recirculation system:
For temperature control, a heat exchanger (Systemair) is mounted in the recirculation section for indirect temperature control.
The air is conveyed by a radial tube fan (Cosmo), heating is provided by an electric heater integrated in the brine circuit,
electric heater (Türk and Hillinger) integrated into the brine circuit.
The heaters are continuously monitored by temperature monitors and limiters (Türk and Hillinger, Johnsson Controls).
Cooling is provided by a secondary brine circuit with pumps (KSB) and 3-way valve (Belimo).
Installed electrical heating capacity 1 * 6kW.
The mixing ratio is 50% water / 50% ethylene glycol.
Feeding from station: =TME2++AS-QF21
Operating voltage: 400V
Power: 17kW
Rated current: 33A
Back-up fuse: 35A
Control voltage: 24V DC /24V AC /230V AC
PLC - System: S7 300
Type: IPETRONIK indoor simulation box
Condition: used / used
Scope of delivery: (see picture)
(Changes and errors in the technical data, specifications are reserved!)
Further questions we can answer on the phone for you.

آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.