نیمه یدک‌کش با سکوی کاری

FAYMONVILLE Telemax Sattelauflieger - hydr. gelenkt

You will find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website.

Excerpt from the equipment list. Full specification available on request.
Kwodpfxoyvnd No Agbew

LOADING PLATFORM:
* Gooseneck, length approx. 3,900 mm with central beam
* Loading platform with double-extension, length approx. 9,300 mm
* A support table approx. 200 mm wide is permanently welded to the central beam
* Pneumatic locking with conical locking pin and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective loading platform length (except for the supply to the first and second lock)
* Technical fifth wheel load: 25,000 kg for tractor units: 4x2, 6x2 and 6x4
* TPMS tire pressure monitoring system according to ECE R 141
* BPW axles and suspension, all axles forced steered hydro-mechanically, mounted on turntables
* Technical axle load: 12,000 kg each. Air suspension with lifting and lowering valve
* 275/70 R 22.5 3PMSF twin tyres. Brand of our choice
* ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets
* 3 kW electro-hydraulic unit for hydraulic operations
* 3 pairs of recessed lashing rings in the outer frame of the gooseneck, foldable outward
* At the king pin 1 pair of lashing rings (LC 10,000 daN) – all other lashing rings (LC 5,000 daN)
* 3 pairs of stake pockets integrated in the outer frame of the gooseneck, for plug-in stakes approx. 100 x 50 mm
* 1 crosswise stake pocket bar mounted in the floor of the gooseneck, for plug-in stakes approx. 100 x 50 mm
* 1 at the rear of the gooseneck
* 2" king pin
* Mechanical landing gear with 2-speed gearbox and crank
* 8 pairs of stake pockets integrated in the outer frame of the loading platform, for plug-in stakes approx. 100 x 50 mm
* 10 pairs of recessed lashing rings lying in the outer frame of the loading platform, foldable outward
* Rear and front steering operable via cable remote control, with single-track axle control, no installation in the tractor unit required
* Last axle with air suspension venting activated when the parking brake is applied
* Steel front wall, approx. 1,600 mm high, certified according to EN 12642: 2016 XL
* Round NATO socket at the front connection bar (Maeler & Kaege VG 96 917)
* 1 LED work light each left and right at the landing gear, wired to the tractor unit connection
* Wooden floor approx. 32 mm thick on the gooseneck and loading platform
* At the extension tube with large cross-section, one locking position every approx. 500 mm
* At the extension tube with small cross-section, one locking position every approx. 1,000 mm, allowing for locking every approx. 500 mm
* Cut-outs in the outer frame of the loading platform for hooking lashing straps (LC 2,500 daN)
* 4 crosswise stake pocket bars mounted in the loading platform floor, for plug-in stakes approx. 100 x 50 mm
* 4 wheel chocks with holder under the loading platform
* 1 lockable INOX toolbox, approx. 2,390 x 800 x 500 mm (L x W x H), mounted under the loading platform on the left in direction of travel
* 1 additional lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading platform on the right in direction of travel
* 1 LED work light each left and right in front of the axles, with wiring
* 2 axle load gauges mounted on the left side including axle load diagram
* 1st axle with automatic lift axle function as well as starting...

آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.