نیمه یدک‌کش با سکوی کاری

ES-GE 3-Achs Sattelanhänger - Rungen + CV

You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website.

Excerpt from the equipment list. Complete equipment list available upon request.

Chassis:
* Welded construction made of high-quality steel profiles with continuous profile crossmembers, designed for high point loads
* Underrun protection, width approx. 700 mm
* Outer frame as a UNP profile
* Wear plate approx. 8 mm
* Neck height at the front approx. 130 mm
* Coupling device, 2-inch kingpin
* Underrun guard, bolted design, according to EC
* Side underrun guard according to EC, made of aluminum profiles, anodized
* Saddle supports 2 x 12 t
* Saddle supports with leveling foot and single-side operation on the right side
* Axles 3 x 9 t air suspension axle assembly
* Disc brakes 22.5, total stroke approx. 180 mm
* Lifting and lowering device via rotary slide valve

Braking System:
* Two-circuit compressed air braking system according to EC with EBS and RSS, automatic load-dependent control
* Spring brake cylinders as parking brake
* Interchangeable coupling heads, permanently mounted on the front crossmember, without connection line to the towing vehicle

Tires:
* 6 tires, 385/55 R22.5 160J on steel rim 11.75 X 22.5 ET 120, manufacturer of our choice
* Tire pressure monitoring system (TPMS) via CAN bus system of the EBS

Load securing:
* 9 pairs of folding lashing rings, evenly distributed, tensile force approx. 5.0 t
* 9 pairs of folding lashing rings, evenly distributed, tensile force approx. 2.0 t
* In the outer frame, holes approximately every 400-600 mm for attaching lashing straps

Front Wall:
* Reinforced steel construction, fixed, approx. 1,400 mm high
* Interior lined with approx. 9 mm screen-printed floor (approx. 1,250 mm high)

Floor:
* Approx. 28 mm Z-hardwood floor recessed into the outer frame with galvanized omega steel profiles

Lighting:
* According to EC, 24 volts, with multi-chamber lights
* LED side marker lights
* LED position lights, white at the front
* LED outline lights at the rear
* License plate lights
* LED guide lights
* 1x15-pin and 2x7-pin connector at the front crossmember

Equipment:
* 2 wheel chocks with holder
* Warning signs ECE 70
* Holder for revolving beacon incl. revolving beacon
* 2 rubber impact buffers at the rear
* Rear access ladder on the right side, foldable and extendable (without platform)
* 1 open box made of perforated sheet, transverse to the direction of travel, approx. 600 x 450 x 2,430 mm, galvanized, behind the axles

Paintwork:
* Front wall: RAL 3002 carmine red
* Chassis: Hot-dip galvanized
Pjdpszahp Ejfx Ad Rjpt
* Outer frame, hot-dip galvanized + RAL 3002 carmine red
* Fifth wheel: aluminum, anodized
* Underrun guard: white (RAL 9016 traffic white)
* Components: galvanized/KTL black
* Rims: silver

Including special accessories:
* First axle can be lifted, with fully automatic, load-dependent lift control
* 10 pairs of stake pockets in the outer frame, evenly distributed
* 4 rows of stake pockets transverse to the loading area
* 20 pcs. stakes made of galvanized tube 80/50, total length approx. 1,200 mm
* Inside the front wall, a magazine for 20 pcs. plug-in stakes
* Container locks for 1 x 40' and 2 x 20' containers, flush at the rear
* Container locks for 1 x 20' container in the middle
* Work light on the lamp carrier (switched on via reverse gear)
* 2 stainless steel toolboxes, approx. 600 x 500 x 500 mm, 1 on the left and 1 on the right

آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.