Excerpt from Equipment: Chassis: Welded construction made of high-quality steel profiles with continuous profile crossmembers, designed for high point loads. Underride guard, width approx. 700 mm, outer frame as a UNP profile, wear plate approx. 8 mm, neck height at the front approx. 130 mm. Coupling device: 2-inch kingpin. Underrun protection: bolted design, according to EC. Side underrun protection: according to EC, made of aluminum profiles, anodized. Saddle supports: 2 x 12 t saddle supports with leveling foot and single-sided operation on the right-hand side. Axles: 3 x 9 t air suspension axle unit, disc brakes 22.5". Total stroke approx. 180 mm, raising and lowering device via rotary slide valve. Braking system: Two-circuit compressed air braking system according to EC with EBS and RSS, automatic load-dependent regulation, spring brake cylinders as parking brake, interlockable coupling heads permanently mounted on the front crossmember, without connection line to the tractor unit. Tires: 6 tires, 385/55 R22.5 160J on steel rim 11.75 X 22.5 ET 120, manufacturer of our choice. Tire pressure monitoring system (TPMS) via CAN bus system of the EBS. Fenders: according to EC. Spare wheel holder: none. Load securing: - 9 pairs of folding lashing rings, evenly distributed, tensile force approx. 5.0 t - 9 pairs of folding lashing rings, evenly distributed, tensile force approx. 2.0 t - In the outer frame, holes for attaching lashing straps are provided every approx. 400-600 mm. Front wall: Reinforced steel construction, fixed, approx. 1,400 mm high. Internally lined with approx. 9 mm screen-printed material (approx. 1,250 mm high). Floor: approx. 28 mm Z-hardwood floor recessed in the outer frame with galvanized omega steel profiles. Lighting system: according to EC, 24 Volt, with multi-chamber lights, LED side marker lights, LED position lights white at the front, LED outline lights at the rear, license plate lights. Lane departure warning lights LED. 1x15- and 2x7-pole plug connections on the front crossmember. Equipment: - 2 wheel chocks with holder - Warning signs ECE 70 - Holder for rotating beacon, incl. rotating beacon - 2 rubber impact buffers at the rear - Access ladder at the rear right, foldable and extendable (without platform) - 1 open box made of perforated sheet, transverse to the direction of travel, approx. 600 x 450 x 2,430 mm, galvanized, behind the axles. Painting: Front wall: RAL 3002 carmine red. Chassis: hot-dip galvanized. Outer frame: hot-dip galvanized + RAL 3002 carmine red. Center beams: RAL 3002 carmine red. SSV: Aluminum, anodized. Underrun protection: white (RAL 9016 traffic white). Components: galvanized/KTL black. Rims: silver. Outline marking: complete, yellow. Incl. special accessories. First axle liftable, with fully automatic, load-dependent lift control. 10 pairs of stake pockets in the outer frame, evenly distributed. 4 rows of stake pockets transverse to the loading area. 20 stakes made of galvanized tube 80/50, total length approx. 1,200 mm. Inside the front wall, a magazine for 20 stakes. 5 x 25-mm side boards and rear wall made of anodized aluminum hollow profiles, foldable and removable, removable Kinnegrip stakes. Side board and stake magazine: under the chassis, left and right, sliding rails for side boards and stakes. Container locks for 1 x 40' and 2 x 20' containers, rear-flush. Container locks for 1 x 20' container in the center. Work lights on the lamp carrier (switched via reverse gear). 2
Psdpfx Aezrq U Hegrjra
آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.
