تریلر کم‌ارتفاع نیمه‌کشنده

DINKEL 3-Achs-Jumbotieflader - 2tlg. Rampen

You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website.

Kodpoz Dmnwofx Ad Rjdt
Excerpt from the equipment. Complete equipment available upon request.

Chassis, gooseneck: Special steel frame made of high-strength fine-grain steels, electrically welded at the connection points, well-dimensioned outer frame. 3-axle arrangement. Wheel arch above the axles with spray mist suppression. All steel parts sandblasted. Lateral impact protection made of anodized aluminum mounted. Increased point load of approx. 30,000 kg over approx. 5,000 mm. Special design in the gooseneck area for maximum possible low-bed length in combination with the AluLeg outrigger supports, instead of telescopic outrigger winches, max. rear pivoting radius of the semi-trailer tractor unit 2,100 mm. Special superstructure with rear girder widening: DINKEL - special superstructure. Self-supporting aluminum roof beam / profile approx. 100 x 100 mm, sliding tarpaulin with plastic flaps. Rear girders can be widened to approx. 4,200 mm (only for loading and unloading). Three sliding girders per side with rubber strap relief. Additional center girder locking in the roof beam and parking position, by means of a pull cable and spring latch. DINKEL - lifting roof, mechanically height-adjustable. Lifting roof height approx. 400 mm, operable on both sides or on one side. Without opening the opposite side and the doors. Additional height adjustment of approx. 480 mm in approx. 40 mm increments, with height adjustment in the girders. Front cover on the front wall for operation under a tarpaulin up to a total height of 4,400 mm. Four rows of stackable approx. 150 mm aluminum slats on the side, with 450 mm pockets at the bottom, above 4 rows of individual pockets. In the upper bed, only 3 rows of insert slats. Evenly distributed spacing. Floor: approx. 27 mm special water-resistant glued beech - screen-printing panels, rough surface. Steel sheet in the wheel arch area. Forklift-compatible according to DIN standard. Outer frame flush with the surface. Brakes: WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (parking/release safety valve). Spring brake cylinders as parking brake. Wabco Smart Board with odometer and unit load display. Including WABCO tire pressure monitoring system. Axles: 3 x 10,000 kg SAF/Sauer with drum brakes in a low-bed design. Air suspension with lifting and lowering device, total stroke approx. 230 mm. Third axle as a friction-controlled trailing axle with electric and mechanical lock. Twin tires: 235/75 R 17.5, -12-ply. Premium brand of our choice, including E-wheel chocks. Lighting: according to EC standard including side lights in LED design. Position lights in LED design. 2 additional reversing lights. 2 work lights on the front wall inside, top. Painting: Chassis with superstructure in RAL color of your choice. Center girders, axles powder-coated black. Corner girders in hot-dip galvanized design. Plastic parts black. Hot-dip galvanized parts unpainted. Rims in factory silver. Special equipment including: - E-supply line 15-pin - Air suspension in ECAS design, operation on the semi-trailer - Overwidth signs front and rear in galvanized, steplessly telescopic design with attached marker lights including sockets for flashing beacons (small signs) - Center girders with additional roof beam locking, by means of a pull cable - operation from below - Sliding tarpaulin support unlocking also from

آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.