Conveyordie magnetprofis
Conveyor
die magnetprofis
قیمت ثابت به اضافه مالیات بر ارزش افزوده
€۳٬۵۲۰
سال ساخت
۲۰۲۵
وضعیت
کارکرده
(کاملاً عملیاتی)
موقعیت
Ursberg 

اطلاعات دستگاه
- نام دستگاه:
- Conveyor
- تولید کننده:
- die magnetprofis
- سال ساخت:
- ۲۰۲۵
- وضعیت:
- تقریباً نو (استفادهشده)
- قابلیت عملکرد:
- کاملاً عملیاتی
قیمت و مکان
قیمت ثابت به اضافه مالیات بر ارزش افزوده
€۳٬۵۲۰
- موقعیت:
- Ursberg, آلمان

جزئیات پیشنهاد
- شناسه آگهی:
- A22159062
- بهروزرسانی:
- آخرین بهروزرسانی در ۲۹.۰۳.۱۴۰۵
توضیحات
The system was manufactured for a customer project but was not put into operation due to a subsequent change in the installation requirements. The conveyor belt is in new condition and is immediately available. This provides the opportunity to purchase the system at a significantly lower price than the new price.
Aluminum angle conveyor with substructure, including adjustable feet and machine feet for leveling uneven surfaces.
Horizontal section: 750mm
Rising section: 2,300mm
Inclination angle at the bend: 60°
Height of the horizontal section: 250mm
Conveyor belt length measured on the floor: 1,900mm
Discharge height: 2,200mm
Design:
Aluminum construction
- 2x profile reinforced 90x45mm
- Full-surface wear plate, 2.0mm, galvanized
Drive roller + deflection roller, S235 steel, welded and machined
Ø100x520mm, crowned, shaft fixed with tension bearings
Laodpfxozfi A As Agdjc
Drive: Gearmotor, 0.55KW, speed 0.53m/sec
Connection 230/400V, 50Hz, protection class IP54
Drive ready for connection up to the motor terminal box
(Commissioning must be carried out by a qualified electrician)
PU conveyor belt DM 10/2 0+005 PU including wave edge PU petrol matte
Conveyor belt width: 500mm
2 pieces of wave edges, 50mm high, 25mm wide, high-frequency welded
21 pieces of T-40 studs, 300mm long, approx. 300mm spacing
Belt material: 2-layer, particularly dimensionally stable in the transverse direction
In the bend area, the belt is guided on both sides with 2 pressure rollers each.
The belt is designed with a border-free zone of 70mm on both sides.
Due to the wave edge on both sides, the usable width of the conveyor belt is reduced:
Usable width: 300mm, as follows:
(Top view) Transverse arrangement: 70+25+5+300+5+25+70mm
Belt guidance via PVC wedge strip on the running surface, profile - 10x6mm
- Including recess in the wear plate
- Including sliding joints in the drive and deflection roller
Inspection possible after consultation
Price is net, plus 19% VAT.
آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.
Aluminum angle conveyor with substructure, including adjustable feet and machine feet for leveling uneven surfaces.
Horizontal section: 750mm
Rising section: 2,300mm
Inclination angle at the bend: 60°
Height of the horizontal section: 250mm
Conveyor belt length measured on the floor: 1,900mm
Discharge height: 2,200mm
Design:
Aluminum construction
- 2x profile reinforced 90x45mm
- Full-surface wear plate, 2.0mm, galvanized
Drive roller + deflection roller, S235 steel, welded and machined
Ø100x520mm, crowned, shaft fixed with tension bearings
Laodpfxozfi A As Agdjc
Drive: Gearmotor, 0.55KW, speed 0.53m/sec
Connection 230/400V, 50Hz, protection class IP54
Drive ready for connection up to the motor terminal box
(Commissioning must be carried out by a qualified electrician)
PU conveyor belt DM 10/2 0+005 PU including wave edge PU petrol matte
Conveyor belt width: 500mm
2 pieces of wave edges, 50mm high, 25mm wide, high-frequency welded
21 pieces of T-40 studs, 300mm long, approx. 300mm spacing
Belt material: 2-layer, particularly dimensionally stable in the transverse direction
In the bend area, the belt is guided on both sides with 2 pressure rollers each.
The belt is designed with a border-free zone of 70mm on both sides.
Due to the wave edge on both sides, the usable width of the conveyor belt is reduced:
Usable width: 300mm, as follows:
(Top view) Transverse arrangement: 70+25+5+300+5+25+70mm
Belt guidance via PVC wedge strip on the running surface, profile - 10x6mm
- Including recess in the wear plate
- Including sliding joints in the drive and deflection roller
Inspection possible after consultation
Price is net, plus 19% VAT.
آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.
ارسال درخواست
این آگهیها ممکن است برای شما نیز جالب باشند.
آگهی کوچک
Ursberg
۴٬۰۰۳ km
die magnetprofisPEM1200
آگهی کوچک
Abtenau
۳٬۷۷۳ km
AUERTECHBlockhausfräse BL100A, Bj.2006
آگهی کوچک
Dinkelscherben
۳٬۹۹۲ km
die magnetprofisModel 1000 x 1000mm
آگهی کوچک
Dinkelscherben
۳٬۹۹۲ km
die magnetprofis1500x500+W+U
آگهی کوچک
Roches-Prémarie-Andillé
۴٬۷۴۳ km
KRUZI
آگهی کوچک
Dinkelscherben
۳٬۹۹۲ km
die magnetprofisModel 1000 x 800mm
آگهی کوچک
Dinkelscherben
۳٬۹۹۲ km
die magnetprofis2021090217
آگهی کوچک
Liverpool
۵٬۰۰۳ km
CAMAMTAC1
آگهی کوچک
Ursberg
۴٬۰۰۳ km
die magnetprofis2022042210
آگهی کوچک
Ursberg
۴٬۰۰۳ km
die magnetprofisDMPM2000
آگهی کوچک
San Giovanni Al Natisone
۳٬۷۳۹ km
FriulmacDual Feed
آگهی کوچک
Ursberg
۴٬۰۰۳ km
die magnetprofisPEM1200
آگهی کوچک
Ursberg
۴٬۰۰۳ km
die magnetprofisDMPMFG200x200
آگهی کوچک
Dinkelscherben
۳٬۹۹۲ km
die magnetprofisModel 1000 x 500mm
آگهی شما با موفقیت حذف شد
یک خطا رخ داده است




































































