Lowbed

Fliegl VTS S 400 Parab/Hydr.

Additional Information
Low-bed semi-trailer chassis
Steel welded construction
Turntable with heavy-duty ball bearing ring
Folding rear outriggers
2 support wedges with holder
Aluminum side impact protection
Rear splash guards covering the entire width
Semi-fender for 1st and 2nd axles with anti-spray splash guards behind each axle, anti-spray splash guards in front of and behind the 3rd and 4th axles
Excavator arm recess above the rear axles, extending to the rear, approximately 1800 mm long, approximately 650 mm wide and approximately 150 mm deep, 2 pairs of lashing points of 5 tons each in the excavator arm recess, laterally on the longitudinal frame, approximately 300 mm from the front and approximately 200 mm in front of the rear slope
1 plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with a padlock (lock not included)
1 storage box recessed in the gooseneck at the bottom with lid, W=720 mm/ L=520 mm / D= 170 mm
Extendable widening elements to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm)
Wooden planks 70 mm for widening to 3000 mm
Storage compartment for wooden planks under the loading platform
Lashing eyes for low-bed trailer (40 lashing options)
1 pair of lashing eyes on the gooseneck, each 5 tons
9 pairs of lashing eyes embedded above and on the side in the outer frame, each 10 tons
2 x at the front on the gooseneck
7 x in the low bed
6 pairs of lashing eyes in the outer frame from the low bed, each 5 tons (for attaching tie-down straps)
3 pairs of folding lashing eyes additionally, each 10 tons
1 x inside next to the main frame at the beginning of the low bed
1 x on the gooseneck (protruding)
1 x behind the last axle, recessed in the floor
Lrodei Ri Daopfx Almop
Coupling device for the trailer turntable
Drawbar with tested 50 mm drawbar eye, drawbar eye inclined by 8° / D-value min. 160 kN
Axles + Suspension
Drum brake axles
Parabolic spring suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization at the front and rear (rocker equalization)
Wheels and Tires
235 / 75 R 17.5
according to the manufacturer's choice
Steel rims in twin arrangement, factory silver
Braking System
2-line compressed air braking system
Spring-loaded parking brake
2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle,
ABS and ALB, with ABS connector at the front, with connecting cable
Electrical System
24 Volt, multi-chamber lights, yellow LED lighting on the sides
2 white position lights at the front
2 white/red side marker lights at the rear
2 x 7-pole fail-safe plugs at the front, with connecting cable,
1 LED rotating beacon with holder, switched via parking lights (beacon removable)
2 pairs of warning signs double LED illuminated and extendable to 3,000 mm
Floor
Gooseneck at the front with steel / checkered plate covering
followed by 70 mm softwood floor, wheel arch area with steel / checkered plate covering
Rear slope with 70 mm softwood floor
Ramps
Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable
covered with wood
Hydraulically operated via towing vehicle auxiliary drive with throttle, operation on the left-hand side at the front
Hydraulic connection with SVK plug NW 10/3, incl. connecting hose
Country of Registration / Signs
Country of Registration: Germany
24/7 Service Hotline
prepared for two-line license plate holder
Contour marking with reflective strips ac

آگهی به صورت خودکار ترجمه شده است. احتمال بروز اشتباه در ترجمه وجود دارد.